Philips Soundbar Universal Remote Codes & Program Instructions

We have enough amount of universal remote codes for your Philips Soundbar. So, if you do wanna control your Philips Soundbar then simply use the below 4 and 5 digit codes and then program them with the below methods. Once you got the correct codes and method then you can control this philips soundbar with universal remote control, CABLE remote or with the SAT remote too.

If you want universal remote codes for philips tv check out this article

Philips Soundbar Universal Remote 4 Digit Codes

  • 0729
  • 1798
  • 1805
  • 0296
  • 1216
  • 1296
  • 1116
  • 1316
  • 0216
  • 0177
  • 0083
  • 0983
  • 0084
  • 0184
  • 0277
  • 0377

Also check: philips dvd player remote codes

Philips Soundbar Universal Remote 5 Digit Codes

32459, 32311, 30189, 20081, 31266, 20035, 20618, 20739, 11454, 10054, 10037, 10690, 11483

Check Out: how to program a universal remote to a philips blu ray player

These codes cam work with All These Philips soundbar models CSS2133B/F7, HTL9100/12, HTL2163B, HTL3110B/F7, HTL2101A/F7, B5/37 Fidelio, HTL7180/F7, HTL4115B, HTL2101/F7 and CSS2123B/F7.

You can even search for the codes by using the code search method on your CAB or SAT remote. The methods has mentioned below.

Using Xfinity? Use the remote code 32459 or 32311.

Actually, with AUX button the volume works but power does not work, But if you wanna fix this issue you can by below steps.

When the remote is in the cable mode then we can easily make to work volume buttons for this Philips soundbar.

  • Once press the “TV” button
  • Hold “Setup” button on your remote until tv button blinks two times
  • On your remote press “9 9 3” numbers to enter them manually
  • Now tv button blinks “Twice”
  • Then Press and Release “AUX” button once
  • After AUX button gives “Flash for 2 Times”
  • Now “Turn off or down” your television speakers
  • “Push” cable button once

(Keep In Mind: The volume button can control only philips soundbar volume but not the Television and the power button can not switch off philips)

Code Search using silver Philips Soundbar remote with a red OK/Select button:

  • “Switch On” Philips soundbar
  • Press and release “AUX” button
  • Hold “Setup” button on your remote until tv button blinks two times
  • After releasing the set up button enter this code “9 9 1 3”
  • Now “AUX” key blinks twice now
  • Aim the remote to your philips sundbar by pressing “Power”
  • Now hold on “CH+” until soundbar turns off
  • In this CODE SEARCH MODE, your remote control sends IR CODE from its library to its selected device.
  • So, press “Setup” once then it will “Lock the Code”
  • If it’s done then “AUX key Blinks Twice”

DIRECTV or ATT with DIRECTV Remote Control:

  • “Switch On” Philips soundbar
  • Keep “Volume UP” but “Muted”
  • Chose “AV1” or “AV2”
  • Keep on holding “Mute” and “Select” buttons simultaneously up to 2 blinks
  • Now enter the code “9 9 1” and then wait for 2 blinks
  • Then enter “3”
  • Press and release “VOL UP”
  • Point your remote at Philips soundbar and then keep on pressing and releasing the “CH UP” button
  • Whenever you observe changes in volume then press “Select” to lock that code.

If DirecTV remote controls the power of the Philips soundbar but not volume, try this:

  • Select “AV1” or “AV2”
  • Now press and hold “Select” and “Mute” buttons
  • You need to wait for “2 Blinks” and then “Release”
  • Enter “9 9 3” now
  • After that press “Select”

You can also check the below methods.

How to Program Philips Soundbar Universal Remote With Auto Search

In the auto search method, all the universal remote codes are gone through scanning process in the remote. It scans one code at a time to find out the correct remote code that works with your remote to program the control. Follow the instructions given below:

  1. “Switch On” the smart device like “TV” that you want the universal remote to operate.
  2. “Turn on” the remote, tap on the device button (TV, DVD, CBL and OK/SEL) for 3 seconds. The LED light indicates the device is ready to program.
  3. Point out the remote to device and click on “CH+” & “CH-“ switches. Remote will show on/off signals. Press “up” or “down” key continuously till the device will turn off.
  4. Verify the code by clicking on “power” key. Device should turn on. If it starts, try changing the channel to verify that remote is programmed correctly.
  5. Now tap the “device” button to save the code. LED of Device will blink twice for confirming the code stored.

How to Program Philips Soundbar Universal Remote With Manual Method

By using the keycode we can easily program a universal remote and the keycode identifies the make and model of your equipment.

  • First you need to “Turn The Device On”
  • Press the “TV” on your “Philips Soundbar universal remote”
  • Now press and hold the “Setup button” of the Universal Remote until it shows the “Light Flash” (It means it is in “Learning mode”)
  • ¬†Finally enter the “Keycode” which you collected from the programing guide (Instructions Booklet)
  • Once you’ve done this procedure, just “point your remote at the TV” and then “Press And Hold The Power” button
  • You can release the “Power Button” whenever the screen switches off

That’s all, your TV will work perfectly now with the universal remote control, if your device is not working then try to repeat the same procedure with the different code from the same part of the reference table.

How to Program Philips Soundbar Universal Remote With Code Search

If you couldn’t find the key code which works for the device at that time you can setup your universal remote to search mode for the correct one. Its a code in manual which forces the remote into the search mode

  • First of all “Turn The Device On”
  • Now press and hold the “Setup” button
  • Enter the “9-9-1” (three digit) code
  • Now hold down the “Power Button” on the remote and then press the Channel up them until the device in this case your tv “Turns Off”

The above method might take some extra time but it is very important to find your key code. Once you have done the above procedure your remote should be working for all the in functions.

Speak Your Mind

*