Soniq Universal Remote Codes & Program Instructions

For your soniq tv we have universal remote codes for any types of universal remote controls. If you would like to soniq tv pairing code then you must try the below codes and then you will be using the universal remote for your soniq tv.

This is the best platform to get your favorite universal’s remote control codes and the codes were mentioned below, you have to try them one by one until your remote will be paired with your favorite universal remote. Then why late just dive into the codes list now and first try these 2 codes 1497, 1328, if these codes not working then try below.

Soniq Universal Remote 4 Digit Codes

1473, 0178, 0180, 0003, 0092, 0045, 0019, 0030, 0056, 0032, 0047, 0054, 0060, 0039

Soniq Universal Remote 3 Digit Code


Soniq Universal Remote 5 Digit Code


Audiosonic Universal Remote Code For Soniq tv


Skandia Universal Remote Code For Soniq

2551, 2791

How To Program Soniq TV Universal Remote?

If you want to pair your soniq  tv remote with your favorite universal remote control then you should know the procedure to enter the code you have to check the below methods.

  • Turn your “TV On”
  • Simultaneously press and hold the “TV” and “SEL” buttons until the “Button Will Light”
  • Point the remote at the TV with the button lit and then enter your TV’s “3 or 4 or 5 Digit Code”
  • Now press the “Volume + Button” to verify and you can observe your TV’s volume is rising
  • Now press the TV button then it will “store 3 or 4 or 5 digit code”. The button will be blinking twice which means your device codes have been stored successfully.

First you have to follow this method and then you can follow the below methods if the above mentioned method doesn’t work properly.

How to Program Soniq Universal Remote With Keycode

By using the keycode we can easily program a universal remote and the keycode identifies the make and model of your equipment.

  • First you need to “Turn The Device On”
  • Press the “TV” on your “Soniq Universal Remote”
  • Now press and hold the “Setup button” of the Universal Remote until it shows the “Light Flash” (It means it is in “Learning mode”)
  •  Finally enter the “Keycode” which you collected from the programing guide (Instructions Booklet)
  • Once you’ve done this procedure, just “point your remote at the TV” and then “Press And Hold The Power” button
  • You can release the “Power Button” whenever the screen switches off

That’s all, your TV will work perfectly now with the universal remote control, if your device is not working then try to repeat the same procedure with the different code from the same part of the reference table.

How to Program Soniq Universal Remote With Code Search

If you couldn’t find the key code which works for the device at that time you can setup your universal remote to search mode for the correct one. Its a code in manual which forces the remote into the search mode

  • First of all “Turn The Device On”
  • Now press and hold the “Setup” button
  • Enter the “9-9-1” (three digit) code
  • Now hold down the “Power Button” on the remote and then press the Channel up them until the device in this case your tv “Turns Off”

The above method might take some extra time but it is very important to find your key code. Once you have done the above procedure your remote should be working for all the in functions.

How to Program Soniq Universal Remote With Manual Setup

If the above two methods can’t be helped to you then the final method is “Manual Setup”, if you configure the universal remote control manually your device can work perfectly.

  • Place the “Remote Control facing To The Universal remote control you want to replace”
  •  Now press the “Setup Button” or “Magic”
  • Then enter the “Code” (You can find this in Instruction Booklet) for manual Programming
  • Now press any of the function which you want to “program” for instance “TV Volume Up”
  • Then press And hold the corresponding key on the “Original Remote Controller”
  • Finally, one of the lights will “blink” that means it has been saved correctly
  • Now your “TV Volume Up” button has been saved to the Universal remote and you can use the volume button.

You have to repeat for all the buttons to program, once you have done to all the functions which you want and finally press the “Setup Button” Again to finish the session.

With the above three methods we can easily Program Our Soniq TV’s  Device Universal Remote.


If you found the above codes worked for your device then please share this article as many people as possible, there are so many users who are eagerly waiting for these codes so share them and program your tv remote with your favorite universal remote control.

Speak Your Mind