Sanyo Soundbar Universal Remote Codes

In this blog post we are gonna mention all working codes and the best programing methods for sanyo Soundbar. Actually, the sanyo Soundbar can be controlled with different types of universal remote controls and CAB or SAT remotes. So no matter what device you’re using to control sanyo Soundbar but you should follow the codes and programing methods too. So check them below now.

We’ve mentioned three and five digit codes below so check them one by one.

Sanyo Soundbar Universal Remote 3 Digit Codes

  • 590
  • 611
  • 627
  • 661
  • 683

Sanyo Soundbar Universal Remote 4 Digit Codes

  • 0157
  • 1156
  • 1166
  • 1176

Sanyo Soundbar Universal Remote 5 Digit Codes

  • 20047
  • 10154
  • 10159
  • 10051
  • 10250
  • 20035
  • 30189
  • 30531
  • 20081
  • 21593
  • 20593
  • 20000
  • 20039
  • 20149
  • 21781

If you find these remote codes are not working for your device then try to follow code search on your CAB or SAT remote…

ATT Remote RC7X:

You can program sanyo soundbar with the RC7X remote control check the steps below:

  • Go to “Menu”
  • Chose “Settings”
  • Then select “Settings & Help”
  • Then “Remote Control”
  • Select “Audio Device” now

With DIRECTV Or ATT As Your Cable With DIRECTV Remote Control:

  • Switch on “Sanyo Soundbar”
  • Click on “VOL+” but “Muted”
  • Chose “AV1” or “AV2”
  • Keep press and hold “Mute” and then “Select” until it gives “2 blinks”
  • Enter the “9 9 1” code and wait for 2 blinks
  • Now enter “3”
  • Then press and release “VOL+”
  • Now face the remote to the sanyo soundbar and then keep on pressing and releasing the “CH+” key
  • You can observe that your device is changing the volume, at that time press “Select” so it will lock the code.

If DIRECTV remote controls the power of the Sanyo soundbar but not volume, try this:

  • Select “AV1 or AV2”
  • Then keep on press and hold the “Mute & Select” buttons
  • Just wait until it gives “Two Blinks” and then release
  • Now enter the code “9 9 3”
  • Finally press “Select”

Code Search using silver Comcast remote with a red OK/Select button:

  • Switch on “Sanyo Soundbar”
  • Once click on “AUX”
  • Now press and hold “Setup” till you observe key blinks twice
  • Now release “Setup”
  • Enter “9 9 1 3”
  • Now “AUX” key will blink twice
  • Then press “Power” after that target your remote control to sanyo soundbar
  • Now keep on press “CH+” until the sound bar turn off
  • Important PointIn this code search mode, the remote control sends IR code from its library to your selected device.
  • Then press “Setup” so that the code will be “Locked”
  • For confirmation the aux key will “Blink Twice”

With a Comcast Xfinity remote with the red ok button:

  • First press “AUX” and then press and hold “Setup” until its blinks two times
  • Now “Enter the code” which we mentioned above.

With a Comcast Xfinity remote with the red ok button – To lock to the Sanyo soundbar:

  • Keep on hold “Setup” until it blinks twice
  • Now enter code “9 9 3”
  • Then press “AUX”

But to take the lock off and then to make it independent of each device:

  • Keep on hold “Setup” until it blinks twice
  • Press the code “9 9 3” and then press once “vol+”

(That’s all you can chose each device which you would wanna change the volume for)

How to Program Sanyo Soundbar Universal Remote With Keycode

By using the keycode we can easily program a universal remote and the keycode identifies the make and model of your equipment.

  • First you need to “Turn The Device On”
  • Press the “TV” on your “Sanyo Soundbar Universal Remote”
  • Now press and hold the “Setup button” of the Universal Remote until it shows the “Light Flash” (It means it is in “Learning mode”)
  •  Finally enter the “Keycode” which you collected from the programing guide (Instructions Booklet)
  • Once you’ve done this procedure, just “point your remote at the TV” and then “Press And Hold The Power” button
  • You can release the “Power Button” whenever the screen switches off

That’s all, your TV will work perfectly now with the universal remote control, if your device is not working then try to repeat the same procedure with the different code from the same part of the reference table.

How to Program Sanyo Soundbar Universal Remote With Code Search

If you couldn’t find the key code which works for the device at that time you can setup your universal remote to search mode for the correct one. Its a code in manual which forces the remote into the search mode

  • First of all “Turn The Device On”
  • Now press and hold the “Setup” button
  • Enter the “9-9-1” (three digit) code
  • Now hold down the “Power Button” on the remote and then press the Channel up them until the device in this case your tv “Turns Off”

The above method might take some extra time but it is very important to find your key code. Once you have done the above procedure your remote should be working for all the in functions.

How to Program Sanyo Soundbar Universal Remote With Manual Setup

If the above two methods can’t be helped to you then the final method is “Manual Setup”, if you configure the universal remote control manually your device can work perfectly.

  • Place the “Remote Control facing To The Universal remote control you want to replace”
  •  Now press the “Setup Button” or “Magic”
  • Then enter the “Code” (You can find this in Instruction Booklet) for manual Programming
  • Now press any of the function which you want to “program” for instance “TV Volume Up”
  • Then press And hold the corresponding key on the “Original Remote Controller”
  • Finally, one of the lights will “blink” that means it has been saved correctly
  • Now your “TV Volume Up” button has been saved to the Universal remote and you can use the volume button.

You have to repeat for all the buttons to program, once you have done to all the functions which you want and finally press the “Setup Button” Again to finish the session.

Speak Your Mind

*