Did you bring a universal remote recently? don’t you know the remote codes for the Dynex TV. In this article we are going to provide all types of universal remote codes for the Dynex TV like three digit and four digit..etc codes you can get them from the below.
We have three methods to setup your Dynex tv with the Universal remote and those methods have been mentioned below. Three methods names are 1) Keycode, 2) Programming Via Universal Remote Code Search and 3) Manual Setup.
- 1 Dynex Universal Remote Codes List
- 2 How to Program Dynex Universal Remote With Auto Search
- 3 How to Program Dynex Universal Remote With Manual Method
- 4 How to Program Dynex Universal Remote With Code Search
Dynex Universal Remote Codes List
|Comcast M1057||0463, 10463, 096|
|Direct TV RC23||10463|
|Dish Network VIP508||720|
|Dish Network VIP622||720|
|One for All URC-6690||0464|
|TiVo SERIES 3||091|
First Try This Codes
Dynex 4 Digit Universal Remote Codes
2049, 2184, 1463, 5311, 3141, 3161, 0371, 2891, 1040, 1181, 1171, 0135, 1718, 0115, 5421
Dynex 5 Digit Universal Remote Codes
10180, 10178, 10171, 10623, 11963, 10096, 10463, 10154, 10236, 10463, 12049, 12184, 11463, 11780, 11785, 11810, 12288, 11631, 13700, 18924, 13153, 11435
Dynex 3 Digit Universal Remote Codes
720, 001, 538, 533, 834, 632, 256, 583, 585, 701, 706, 698, 726, 500, 220, 908, 587, 333, 603, 221, 115, 503, 666, 800, 120, 650, 844, 724, 200
GE Universal Remote Codes For Dynex TV
3141, 5311, 3161, 6521, 0371, 2891
RCA Universal Remote Codes For Dynex TV
Philips Universal Remote Codes Dynex
How to Program Dynex Universal Remote With Auto Search
In the auto search method, all the universal remote codes are gone through scanning process in the remote. It scans one code at a time to find out the correct remote code that works with your remote to program the control. Follow the instructions given below:
- “Switch On” the smart device like “TV” that you want the universal remote to operate.
- “Turn on” the remote, tap on the device button (TV, DVD, CBL and OK/SEL) for 3 seconds. The LED light indicates the device is ready to program.
- Point out the remote to device and click on “CH+” & “CH-“ switches. Remote will show on/off signals. Press “up” or “down” key continuously till the device will turn off.
- Verify the code by clicking on “power” key. Device should turn on. If it starts, try changing the channel to verify that remote is programmed correctly.
- Now tap the “device” button to save the code. LED of Device will blink twice for confirming the code stored.
How to Program Dynex Universal Remote With Manual Method
By using the keycode we can easily program a universal remote and the keycode identifies the make and model of your equipment.
- First you need to “Turn The Device On”
- Press the “TV” on your “Dynex universal remote”
- Now press and hold the “Setup button” of the Universal Remote until it shows the “Light Flash” (It means it is in “Learning mode”)
- Finally enter the “Keycode” which you collected from the programing guide (Instructions Booklet)
- Once you’ve done this procedure, just “point your remote at the TV” and then “Press And Hold The Power” button
- You can release the “Power Button” whenever the screen switches off
That’s all, your TV will work perfectly now with the universal remote control, if your device is not working then try to repeat the same procedure with the different code from the same part of the reference table.
How to Program Dynex Universal Remote With Code Search
If you couldn’t find the key code which works for the device at that time you can setup your universal remote to search mode for the correct one. Its a code in manual which forces the remote into the search mode
- First of all “Turn The Device On”
- Now press and hold the “Setup” button
- Enter the “9-9-1” (three digit) code
- Now hold down the “Power Button” on the remote and then press the Channel up them until the device in this case your tv “Turns Off”
The above method might take some extra time but it is very important to find your key code. Once you have done the above procedure your remote should be working for all the in functions. With the above three methods we can easily Program Our Dynex TV Device Universal Remote.
The above mentioned list is all about the Universal Remote Codes which is helpful to the Dynex TV. If you find any of those codes couldn’t work on your remote you have to try the next code which is mentioned in the list.
If you any extra codes which aren’t mentioned in the above list then leave that code in the below mentioned comment section