Blackweb Blu-Ray Universal Remote Codes

Are you looking for ways on how to operate your blu-ray devices with only one remote? The process is very simple and you can learn it from here along with the correct code to enter. The Blackweb Blu-ray remote is very useful if you aspire to comfortably operate your entertainment system. You only have to use the correct codes for Blackweb Blu-ray remote during the programming process. As long as you have the perfect Blackweb Blu-ray player remote code, you can start setting up the device and enjoy a more relaxing time. Apart from the comforts, you will eliminate a lot of clutter in the room.

Check Out: blackweb universal remote codes

Blackweb Blu-ray Universal Remote Codes List

Check out the best code suited to your device. Depending on the model and brand of your device, we provide the complete list of Blackweb Blu-ray remote codes. Across any device, there is always a specific code and you will find what you need in this article. Find the list of Blackweb Blu-ray Universal Remote Codes:

Brand NameBlu-Ray Codes
Funai2378
HITACHI0419, 0150, 0225
HP1810
INSIGNIA1871, 0899, 1874
JVC1789
LG1981, 1980, 2281
MAGNAVOX1934, 1877, 2381, 2287
ONKYO1893
OPPO1855, 2022
PANASONIC1399, 1925, 1923
PHILIPS1976
PIONEER1378
SAMSUNG2399, 1099, 0454, 1908, 2030, 1906
SANYO2273
SHARP1952, 2019
SHERWOOD1824, 1809
SONY1934, 1935, 1936
SYLVANIA3027, 2013, 1878
TCL1825
TOSHIBA1852, 1850, 1851
VIZIO2024, 1770
YAMAHA2017

Also Check: blackweb DVD remote codes

How to Program Blackweb Blu-ray Universal Remote Codes

There are steps you need to follow when trying to program Blackweb remote for Blu-rayplayer. But do not worry because the instructions are easy to understand and only requires a few minutes to set up. To do the process more smoothly, first secure the needed Blackweb Blu-ray player remote codes for the type of device you wish to program. The instructions below will guide you on how to program the device:

How to Program Blackweb Blu-Ray Universal Remote With Auto Search

In the auto search method, all the universal remote codes are gone through scanning process in the remote. It scans one code at a time to find out the correct remote code that works with your remote to program the control. Follow the instructions given below:

  1. “Switch On” the smart device like “TV” that you want the universal remote to operate.
  2. “Turn on” the remote, tap on the device button (TV, DVD, CBL and OK/SEL) for 3 seconds. The LED light indicates the device is ready to program.
  3. Point out the remote to device and click on “CH+” & “CH-“ switches. Remote will show on/off signals. Press “up” or “down” key continuously till the device will turn off.
  4. Verify the code by clicking on “power” key. Device should turn on. If it starts, try changing the channel to verify that remote is programmed correctly.
  5. Now tap the “device” button to save the code. LED of Device will blink twice for confirming the code stored.

How to Program Blackweb Blu-Ray Universal Remote With Manual Method

By using the keycode we can easily program a universal remote and the keycode identifies the make and model of your equipment.

  • First you need to “Turn The Device On”
  • Press the “TV” on your “Blackweb Blu-Ray universal remote”
  • Now press and hold the “Setup button” of the Universal Remote until it shows the “Light Flash” (It means it is in “Learning mode”)
  •  Finally enter the “Keycode” which you collected from the programing guide (Instructions Booklet)
  • Once you’ve done this procedure, just “point your remote at the TV” and then “Press And Hold The Power” button
  • You can release the “Power Button” whenever the screen switches off

That’s all, your TV will work perfectly now with the universal remote control, if your device is not working then try to repeat the same procedure with the different code from the same part of the reference table.

How to Program Blackweb Blu-Ray Universal Remote With Code Search

If you couldn’t find the key code which works for the device at that time you can setup your universal remote to search mode for the correct one. Its a code in manual which forces the remote into the search mode

  • First of all “Turn The Device On”
  • Now press and hold the “Setup” button
  • Enter the “9-9-1” (three digit) code
  • Now hold down the “Power Button” on the remote and then press the Channel up them until the device in this case your tv “Turns Off”

The above method might take some extra time but it is very important to find your key code. Once you have done the above procedure your remote should be working for all the in functions.

Conclusion

Have you successfully programmed your Blackweb remote with Blu-ray player using any of the codes mentioned above? Or are you having difficulty to program the device? Don’t hesitate to message us and share your experience. Your experiences and suggestions will help improve our site and help other readers also. Feel free to leave your message below.

Speak Your Mind

*