RCA Soundbar Universal Remote Codes

Would you wanna control your RCA Soundbar either with universal remote controls, TV remote, Cable remote, or with SAT remote then you can now by using the codes which we mentioned below and with the help of programing methods. So, once check the codes below and enter them as per the below methods.

If you find any of those codes not working then go with another code and repeat this procedure with different codes from that list and your soundbar will be programed with your favorite universal remote control.

RCA Soundbar Universal Remote 5 Digit Codes ( Most Worked Codes)

  • 20060
  • 31254
  • 30531

RCA Soundbar Universal Remote 5 Digit Codes

  • 20149
  • 20042
  • 21060
  • 21014
  • 31023
  • 21035
  • 20807
  • 20035
  • 32041
  • 33297
  • 32655
  • 30531
  • 31609
  • 31390
  • 31511
  • 33969
  • 33295
  • 32426
  • 31459
  • 31963
  • 30823
  • 31023
  • 33363
  • 33091
  • 30360

How to Program RCA Soundbar Universal Remote With Keycode

By using the keycode we can easily program a universal remote and the keycode identifies the make and model of your equipment.

  • First you need to “Turn The Device On”
  • Press the “TV” on your “RCA Soundbar Universal Remote”
  • Now press and hold the “Setup button” of the Universal Remote until it shows the “Light Flash” (It means it is in “Learning mode”)
  •  Finally enter the “Keycode” which you collected from the programing guide (Instructions Booklet)
  • Once you’ve done this procedure, just “point your remote at the TV” and then “Press And Hold The Power” button
  • You can release the “Power Button” whenever the screen switches off

That’s all, your TV will work perfectly now with the universal remote control, if your device is not working then try to repeat the same procedure with the different code from the same part of the reference table.

How to Program RCA Soundbar Universal Remote With Code Search

If you couldn’t find the key code which works for the device at that time you can setup your universal remote to search mode for the correct one. Its a code in manual which forces the remote into the search mode

  • Turn your “RCA Soundbar” to “ON” Mode
  • Then hit on “AUX”
  • Now press and hold setup until your remote key blinks for twice
  • After that release “Setup”
  • Then enter the code “9 9 1 3”
  • After entering the code the “AUX key will blink twice”
  • Aim your remote control to the RCA Soundbar and then “Press Power”
  • Now click on “CH+” until your RCA sound bar turn off
  • You can observe: in this code search mode, your remote control sends IR Codes from its library to your device
  • So to lock that code once press “Setup”
  • Finally, the “AUX key” will blink twice

The above method might take some extra time but it is very important to find your key code. Once you have done the above procedure your remote should be working for all the in functions.

How to Program RCA Soundbar Universal Remote With Manual Setup

If the above two methods can’t be helped to you then the final method is “Manual Setup”, if you configure the universal remote control manually your device can work perfectly.

  • Place the “Remote Control facing To The Universal remote control you want to replace”
  •  Now press the “Setup Button” or “Magic”
  • Then enter the “Code” (You can find this in Instruction Booklet) for manual Programming
  • Now press any of the function which you want to “program” for instance “TV Volume Up”
  • Then press And hold the corresponding key on the “Original Remote Controller”
  • Finally, one of the lights will “blink” that means it has been saved correctly
  • Now your “TV Volume Up” button has been saved to the Universal remote and you can use the volume button.

You have to repeat for all the buttons to program, once you have done to all the functions which you want and finally press the “Setup Button” Again to finish the session.

Speak Your Mind

*