If you wanna control your yamaha soundbar by using the universal remote control or SAT or else with the CAB remote controls then you need to use their codes which are designed especially for this yamaha soundbar.
If you’ve the best working codes and correct programing methods then it is easy to control your yamaha soundbar with the universal remote control. We are mentioning the codes below and also the methods too. Check out now.
Contents
Yamaha Soundbar Universal 5 Digit Remote Codes
- 31947
- 31331
- 30176
- 31176
- 30354
- 10030
- 10797
- 10017
- 10019
Xfinity Remote Code For Yamaha Sound Bar
- 992 ( Note to use this code follow below mentioned code search method)
By using the above mentioned remote codes you can program the remote with your yamaha soundbar. You can find the steps for how to program your remote to work with the soundbar. So check the steps below.
How To Program Yamaha Soundbar Universal Remote?
Uuse the below method for yamaha soundbar (codes 30176 or 31331)
(There has to be a TV code programmed to the TV device or the volume keys will not work)
- AV1 or AV2
- Press and hold the MUTE & SELECT, you need to wait here for two blinks and then release it
- Now enter 30176 and then AV1 or AV2
- Now Press and Hold Mute & Select again wait for two blinks and then release it
- Now Enter 993 code
- Press Select
- Then AV1 or AV2
- Now press & Hold Mute & Select then wait here for two blinks and then release it
- Now enter 963
- Press CH Down
- Now you need to enter the commands from the directv att remote control.
Or you can use the below method too….
Use code 30176 or 31331 for the Yamaha Sound bar
(There has to be a TV code programmed to the TV device or the volume keys will not work)
-AV1 or AV2
-Press and hold MUTE & SELECT until it gives 2 blinks
-Enter 993 code
-Hit on SELECT
Actually the above mentioned codes can also be used for programing the yamaha soundbar models. The models are:
ATS-1030, YSP-1000, YSP-5100, YSP-4100, YSP-1400, YAS-101, YAS-103, YHT-S400, and YSP-4000BL
Those codes have been tested with the following devices:
Comcast remote controls, Xfinity XR5, DVR 3 device remote, XR2 Remote, Xfinity XR2 U2, XR2 R2, DirecTV, Directv HR24 STB, S10-S4, U-verse remote control, RC65, Satellite H20 Receiver, DirecTV Plus HD DVR, Comcast 3-in-1 remote, and 1067BG3.
How to Program Yamaha Soundbar Universal Remote Without Codes
In the auto search method, all the universal remote codes are gone through scanning process in the remote. It scans one code at a time to find out the correct remote code that works with your remote to program the control. Follow the instructions given below:
- “Switch On” the smart device like “TV” that you want the universal remote to operate.
- “Turn on” the remote, tap on the device button (TV, DVD, CBL and OK/SEL) for 3 seconds. The LED light indicates the device is ready to program.
- Point out the remote to device and click on “CH+” & “CH-“ switches. Remote will show on/off signals. Press “up” or “down” key continuously till the device will turn off.
- Verify the code by clicking on “power” key. Device should turn on. If it starts, try changing the channel to verify that remote is programmed correctly.
- Now tap the “device” button to save the code. LED of Device will blink twice for confirming the code stored.
How to Program Yamaha Soundbar Universal Remote With Manual Method
By using the keycode we can easily program a universal remote and the keycode identifies the make and model of your equipment.
- First you need to “Turn The Device On”
- Press the “TV” on your “Yamaha Soundbar universal remote”
- Now press and hold the “Setup button” of the Universal Remote until it shows the “Light Flash” (It means it is in “Learning mode”)
- Finally enter the “Keycode” which you collected from the programing guide (Instructions Booklet)
- Once you’ve done this procedure, just “point your remote at the TV” and then “Press And Hold The Power” button
- You can release the “Power Button” whenever the screen switches off
That’s all, your TV will work perfectly now with the universal remote control, if your device is not working then try to repeat the same procedure with the different code from the same part of the reference table.
How to Program Yamaha Soundbar Universal Remote With Code Search
If you couldn’t find the key code which works for the device at that time you can setup your universal remote to search mode for the correct one. Its a code in manual which forces the remote into the search mode
- First of all “Turn The Device On”
- Now press and hold the “Setup” button
- Enter the “9-9-1” (three digit) code
- Now hold down the “Power Button” on the remote and then press the Channel up them until the device in this case your tv “Turns Off”
The above method might take some extra time but it is very important to find your key code. Once you have done the above procedure your remote should be working for all the in functions.
We hope the above methods and the codes have been worked to program your Yamaha Soundbar and also for your favorite remote control. Those methods are used for Yamaha Soundbar remote control setup.
Now we’re going to mention some more methods to fix some issues. So check them once.